PRACA ORYGINALNA
Thermal and Electrical Analysis of Automotive Ignition System
1
Department of Measurement and Application Electrical Engineering, University of Zilina, Slovak Republic
Data nadesłania: 29-01-2019
Data ostatniej rewizji: 12-03-2019
Data akceptacji: 13-03-2019
Data publikacji: 29-03-2019
Autor do korespondencji
Miroslav Gutten
Department of Measurement and Application Electrical Engineering, University of Zilina, Univerzitna 1, 01026, Zilina, Slovak Republic
Department of Measurement and Application Electrical Engineering, University of Zilina, Univerzitna 1, 01026, Zilina, Slovak Republic
The Archives of Automotive Engineering – Archiwum Motoryzacji 2019;83(1):113-121
SŁOWA KLUCZOWE
DZIEDZINY
STRESZCZENIE
This article describes principles of evaluation of individual parts of the ignition system, using conventional diagnostic systems, based on evaluation of current and voltage waveforms. By means of the practical test, diagnostics, measurements and subsequent analysis it was proved that thermovision plays an important role in diagnostics in on-line check automotive equipment. By comparing the non-standard warming behaviour of a part of the electrical system with combination with time high-voltage method, it is possible to diagnose a fault and also check the operating mode of the system. An example of a thermogram of the temperature distribution of the ignition coils and analysis of high-voltage ignition curves with faulty spark plugs is given in part of paper of nondestructive diagnostics with a difference in temperature. Analysing fault condition of ignition systems, using method conventional diagnosis of high-voltage pulse waveforms and also method of thermovision diagnostics, we can adequately evaluated the functionality of the electronic system and its individual components. In some cases, with one coil ignition systems, we cannot use the conventional method and therefore it is preferable to proceed to the analysis of temperature fields.
REFERENCJE (20)
1.
Barta D., Mruzek M. Non-conventional drive and its possibilities of using in road vehicles of public transport. OPT-i 2014 - 1st International Conference on Engineering and Applied Sciences Optimization, Proceedings, 2014, pp. 2049-2061.
2.
Bartlomiejczyk M., Simko M., Chupac M., Hamacek S. Diagnostics of thermal processes in antenna systems of broadcast stations. Przeglad Elektrotechniczny, Vol. 90, No. 4, 2014, pp. 149-152, DOI: 10.12915/pe.2014.04.34.
3.
Brandt, M. Identification failure of 3 MVA furnace transformer. Conference DEMISEE 2016, Papradno, 2016, Slovak Republic, pp. 6-10, DOI: 10.1109/DEMISEE.2016.7530472.
4.
Brandt, M. Experimental measurement and analysis of frequency responses SFRA for rotating electrical machines. Elektroenergetika 2017, Stara Lesna, Slovak Republic, pp. 284-288.
5.
Chen L., Zhang Z. Study on the Measurement of Dynamic Characteristics for Automotive Electronic Fuel Injector. International Conference on Transportation, Mechanical, and Electrical Engineering (TMEE 2011), China, pp. 511-514, 2011, DOI: 10.1109/TMEE.2011.6199253.
6.
Frivaldsky, M., Cuntala, J., Spanik, P., Kanovsky, A. Investigation of thermal effects and lifetime estimation of electrolytic double layer capacitors during repeated charge and discharge cycles in dedicated application. Electrical Engineering, Vol. 100, No. 1, pp. 11-25, DOI: 10.1007/s00202-016-0482-2.
7.
Glowacz A., Glowacz Z. Diagnosis of the three-phase induction motor using thermal imaging. Infrared Physics and Technology, Vol. 81, 2017, pp. 7-16, DOI: 10.1016/j.infrared.2016.12.003.
8.
Glowacz, A., Glowacz, W., Glowacz, Z., Kozik, J. Early fault diagnosis of bearing and stator faults of the single-phase induction motor using acoustic signals. Measurement: Journal of the International Measurement Confederation, Vol. 113, 2018, pp. 1-9. DOI: 10.1016/j.measurement.2017.08.036.
9.
Glowacz, A., Glowacz, W. Vibration-Based Fault Diagnosis of Commutator Motor. Shock and Vibration, 2018, DOI: 10.1155/2018/7460419.
10.
Jia J., Wang Q., Yu J., Zheng Y. Wideband equivalent circuit model and parameter computation of auto-motive ignition coil based on finite element analysis. Application Computational Electromagnetics Society Journal, Vol. 25, 2010, pp. 612-619.
11.
Kanuch J., Ferkova Z. Simulation stepping motor with DISC rotor. International Conference on Low Voltage Electrical Machines, Brno, 2010.
12.
Li X., Lu X., Han G. The Design and Simulation Research of Mazda6 Hybrid Electric Vehicle. Przeglad Elektrotechniczny, Vol. 88, No. 3b, 2012, pp. 44-47.
13.
Mruzek M., Gajdac I., Kucera L., Barta D. Analysis of parameters influencing electric vehicle range. Procedia Engineering, Vol. 134, 2016, pp. 165-174, DOI: 10.1016/j.proeng.2016.01.056.
14.
Pavelek, M., Frivaldsky, M., Spanik, P. Multi-level simulation model of the wireless power transfer system. 12th International Conference ELEKTRO 2018, 2018, pp. 1-4, DOI: 10.1109/ELEKTRO.2018.8398274.
15.
Pavelek, M., Frivaldsky, M., Spanik, P. Distribution and shaping of magnetic field of wireless energy transfer system. EEE International Symposium on Industrial Electronics, pp. 705-710, DOI: 10.1109/ISIE.2017.8001332.
16.
Sebok M., Gutten M., Adamec J., Glowacz A., Roj J. Analysis of the electronic fuel injector operation. Communications - Scientific Letters of the University of Zilina, Vol. 20, No. 1, 2018, pp. 32-36.
17.
Simko M., Chupac, M. Non-destructive method of measurement of radio transmitters antenna systems. Elektronika ir elektrotechnika, Vol. 107, No. 1, 2011, pp. 33-36.
18.
Spanik P., Sedo, J., Drgona, P., Frivaldski M. Real Time Harmonic Analysis of Recuperative Current through Utilization of Digital Measuring Equipment. Elektronika ir Elektronika, Vol. 19, No. 5, 2013, pp. 33-38, DOI: 10.5755/j01.eee.19.5.4364.
20.
Wang I.Q. et al. Circuit model and parasitic parameter extraction of the spark plug in the ignition system. Turk J Elec Eng & Comp Sci, Vol. 20, No.5, 2012, DOI: 10.3906/elk-1009-751.
Korzystamy z plików cookie (oraz innych podobnych technologii) i przetwarzamy unikalne identyfikatory oraz dane przeglądarki – w celu umożliwienia funkcjonowania naszej strony internetowej. Więcej informacji o tym jak przetwarzamy Twoje dane osobowe znajdziesz w
